Give the mini VPN router a minute or two to boot up.Ģ7. You can now turn the mini VPN router off and on again (pull the power on the router and reconnect). Then the other end to the WAN port on your mini VPN router.Ģ6. Give it 30 seconds and switch your ehternet cable from the LAN port on your computer to a LAN port on your primary router. It is the password you'll need to connect to your libreCMC-VPN access point in the steps below. Click the Wireless Security tab and enter a password where it says Key. Change the name from libreCMC to libreCMC-VPN. Under the General Setup there is a box that says ESSID next to it. Scroll down to the bottom of the page where it says Interface Configuration. Network > Wifi and click the Edit button next to where it says the SSID name (libreCMC). Note: If your primary router is using a 192.168.3.x subnet then you will need to change the mini router's subnet to something else.Ģ4. In the IPv4 address change the address to 192.168.3.1. Set the IP to 192.168.3.1 : Network > Interfaces. Enter 84.200.69.80 in the Use custom DNS servers box. Uncheck Use DNS servers advertised by peer to do this. Set DNS server in Network > Interfaces > WAN > Advanced Settings and enter a DNS. Select the librecmc-openvpn-setup/ file you created earlier and click the Upload Archive button. Click Browse button under the Backup / Restore sectionĢ1. Go to System > Backup / Flash FirmwareĢ0. Enter a password and hit save and applyġ9. Click Login (there is no password set by default)ġ7. Other browsers will be slightly different.ġ6. You will also need to click Confirm Security Exception (in Firefox). Click Advanced and Add Exception (in Firefox anyway) so you can continue. Open a browser (you may have to use Firefox) and go to - you will probably get a warning message such as ‘Your connection is not secure’. Open up a web browser and connect the ethernet cable from the lan port on the mini router to your computer (disable wireless on your computer temporarily) and plug the power in wait about 2 minutes for the router to boot upġ5. If you open the file you just created you should see a folder in it called etcġ4. Go to your librecmc-openvpn-setup folder and compress the etc folder (make sure to save it as a tar.gz file, and not a. Option config /etc/openvpn/AirVPN_Netherlands_nfġ2. With the following (but change AirVPN_Netherlands_nf to that of your. Edit librecmc-openvpn-setup/etc/config/openvpn Then remove the quotes from the following lines such that it looks like:ĩ. ovpnįind the following line: explicit-exit-notify 5 and comment out the line so it looks like this: #explicit-exit-notify 5 In the openvpn directory you will need to edit a file that ends in. Rename the AirVPN folder that is extracted in prior command to openvpnħ. Extract to librecmc-openvpn-setup/etc/ and delete the fileĦ. Click the Generate button and click the tar.gz to save the resulting file to your librecmc-openvpn-setup/etc/ directoryĥ. “Terms of Service” Check the boxes that say ‘I have read and I accept the Terms of Service’Īnd ‘I HEREBY EXPLICITLY ACCEPT POINTS 8, 10, 11’Ĥ. On the right you will see a box for ‘Separate keys/certs from. Protocols” Select UDP and then check the ‘Advanced mode’ box. Choose your Operating System” Select Linux Once you have an account go to and select the following configuration: Create a folder in your home directory named librecmc-openvpn-setup and copy the file from the included CD to this directory. Sign up for AirVPN if this is the VPN provider you would like to use at: Ģ. (this is applicable to users who did not purchase VPN service with router, for generic instruction with other VPN providers see README on CD)ġ.
0 Comments
Leave a Reply. |